1 GB/T 2-1985 紧固件 外螺纹零件的末端
Fasteners--Ends of parts with external thread
2 GB/T 8-1988 方头螺栓 C级
Square head bolts--Product grade C
3 GB/T 10-1988 沉头方颈螺栓
Flat countersunk square neck bolts
4 GB/T 11-1988 沉头带榫螺栓
Flat countersunk nib bolts
5 GB/T 12-1988 半圆头方颈螺栓
Cup head square neck bolts
6 GB/T 13-1988 半圆头带榫螺栓
Cup head nib bolts
7 GB/T 15-1988 大半圆头带榫螺栓
Cup head nib bolts with large head
8 GB/T 22-1976 小六角头导颈螺栓
Bolts, small hexagon head with fit neck
9 GB/T 23-1976 小六角头螺杆带孔螺栓
Bolts, small hexagon head with hole through the shank
10 GB/T 24-1976 小六角头螺杆带孔导颈螺栓
Bolts, small hexagon head with fit neck and hole through the shank
11 GB/T 25-1976 小六角头头部带孔螺栓
Bolts, small hexagon head with holes through the head
12 GB/T 26-1976 小六角头头部带孔导颈螺栓
Bolts, small hexagon head with fit neck and holes through the head
13 GB/T 27-1988 六角头铰制孔用螺栓 A和B级
Hexagon fit bolts--Product grade A and B
14 GB/T 28-1988 六角头螺杆带孔铰制孔用螺栓 A和B级
Hexagon fit bolts with Split pin hole on shank--Product grade A and B
15 GB/T 29.1-1988 六角头头部带槽螺栓 A和B级
Hexagon bolts with slot on head--Product grade A and B
16 GB/T 29.2-1988 十字槽凹穴六角头螺栓
Cross recessed hexagon bolts with indentation
17 GB/T 31.1-1988 六角头螺杆带孔螺栓 A和B级
Hexagon bolts with split pin hole on shank--Product grade A and B
18 GB/T 31.2-1988 六角头螺杆带孔螺栓 细杆 B级
Hexagon bolts with split pin hole on shank--Reduced shank--Product grade B
19 GB/T 31.3-1988 六角头螺杆带孔螺栓 细牙 A和B级
Hexagon bolts with split pin hole on shank--Fine pitch thread--Product grade A and B
20 GB/T 32.1-1988 六角头头部带孔螺栓 A和B级
Hexagon bolts with wire holes on head--Product grade A and B
21 GB/T 32.2-1988 六角头头部带孔螺栓 细杆 B级
Hexagon bolts with wire holes on head--Reduced shank--Product grade B
22 GB/T 32.3-1988 六角头头部带孔螺栓 细牙 A和B级
Hexagon bolts with wire holes on head--Fine pitch thread--Product grade A and B
23 GB/T 35-1988 小方头螺栓 B级
Square head bolts with small head--Product grade B
24 GB/T 37-1988 T型槽用螺栓
Bolts for T-Slot
25 GB/T 38-1976 螺栓 技术条件
Bolts--Technical requirements
26 GB/T 39-1988 方螺母 C级
Square nuts--Product grade C
27 GB/T 41-1986 1 型六角螺母 C 级
Hexagon nuts--Style 1--Product grad C
28 GB/T 56-1988 六角厚螺母
Hexagon thick nuts
29 GB/T 61-1976 螺母 技术条件
Nuts--Technical requirements
30 GB/T 62-1988 蝶形螺母
Wing nuts
31 GB/T 63-1988 环形螺母
Lifting nuts
32 GB/T 65-1985 开槽圆柱头螺钉
Slotted cheese head screws
33 GB/T 67-1985 开槽盘头螺钉
Slotted pan head screws
34 GB/T 68-1985 开槽沉头螺钉
Slotted countersunk head screws
35 GB/T 69-1985 开槽半沉头螺钉
Slotted raised countersunk head screws
36 GB/T 70-1985 内六角圆柱头螺钉
Hexagon socket cap head screws
37 GB/T 71-1985 开槽锥端紧定螺钉
Slotted set screws with cone point
38 GB/T 72-1988 开槽锥端定位螺钉
Slotted set screws with cone point
39 GB/T 73-1985 开槽平端紧定螺钉
Slotted set screws with flat point
40 GB/T 74-1985 开槽凹端紧定螺钉
Slotted set screws with cup point
41 GB/T 75-1985 开槽长圆柱端紧定螺钉
Slotted set screws withlong dog point
42 GB/T 77-1985 内六角平端紧定螺钉
Hexagon socket set screws with flat point
43 GB/T 78-1985 内六角锥端紧定螺钉
Hexagon socket set screws with cone point
44 GB/T 79-1985 内六角圆柱端紧定螺钉
Hexagon socket set screws with dog point
45 GB/T 80-1985 内六角凹端紧定螺钉
Hexagon socket set screws with cup point
46 GB/T 83-1988 方头长圆柱球面端紧定螺钉
Square set screws with long dog point and rounded end
47 GB/T 84-1988 方头凹端紧定螺钉
Square set screws with cup point
48 GB/T 85-1988 方头长圆柱端紧定螺钉
Square set screws with long dog point
49 GB/T 86-1988 方头短圆柱锥端紧定螺钉
Square set screws with short dog point and cone end
50 GB/T 89-1976 螺钉 技术条件
Screws--Technical requirements
51 GB/T 90-1985 紧固件验收检查、标志与包装
Acceptance inspection,marking and packaging of fasteners
52 GB/T 91-1986 开口销
Split pins
53 GB/T 93-1987 标准型弹簧垫圈
Single coil spring lock washers--Normal type
54 GB/T 94.1-1987 弹性垫圈技术条件 弹簧垫圈
Specifications for spring washers--Single coil spring lock washers
55 GB/T 94.2-1987 弹性垫圈技术条件 齿形、锯齿锁紧垫圈
Specifications for spring washers--Toothed lock and serrated lock washers
56 GB/T 94.3-1987 弹性垫圈技术条件 鞍形、波形弹性垫圈
Specifications for spring washers--Curved and wave spring washers
57 GB/T 95-1985 平垫圈-C级
Plain washers--Product grade C
58 GB/T 272-1993 滚动轴承 代号方法
Rolling bearing--Identification code
59 GB/T 273.1-1987 滚动轴承 圆锥滚子轴承 外形尺寸方案
Rolling bearings Tapered roller bearings--Boundary dimensions
60 GB/T 273.3-1988 滚动轴承 向心轴承 外形尺寸方案
Rolling bearings Radial bearings-Boundary dimensions
61 GB/T 274-1991 滚动轴承 装配倒角极限
Rolling bearing chamfer dimension limits
62 GB/T 275-1993 滚动轴承与轴和外壳的配合
Shaft and housing fits for rolling bearings
63 GB/T 276-1994 滚动轴承 深沟球轴承 外形尺寸
Rolling bearings--Deep groove ball bearings--Boundary dimensions
64 GB/T 280-1964 带毡封圈的单列向心球轴承 结构型式和基本尺寸
Rolling bearings--Single-row radial ball bearings withfelt seals--Types and basic dimensions
65 GB/T 281-1994 滚动轴承 调心球轴承 外形尺寸
Rolling bearings--Self-aligning ball bearings--Boundary dimensions
66 GB/T 283-1994 滚动轴承 圆柱滚子轴承 外形尺寸
Rolling bearings--Cylindrical roller bearings-Boundary dimensions
67 GB/T 285-1994 滚动轴承 双列圆柱滚子轴承 外形尺寸
Rolling bearings--Double row cylindrical roller bearings-Boundary dimensions
68 GB/T 286-1964 双列向心球面滚子轴承 结构型式和基本尺寸
Rolling bearings--Double -row radial spherical roller bearings--Types and basic dimensions
69 GB/T 288-1994 滚动轴承 调心滚子轴承 外形尺寸
Rolling bearings--Self-aligning roller bearings-Boundary dimensions
70 GB/T 289-1964 滚针轴承 结构型式和基本尺寸
Needle roller bearings--Types and basic dimensions
71 GB/T 291-1964 螺旋滚子轴承 结构型式和基本尺寸
Rolling bearings with helically wound cylindrical rollers--Types and basic dimensions
72 GB/T 292-1994 滚动轴承 角接触球轴承 外形尺寸
Rolling bearings--Angular contact ball bearings--Boundary dimensions
73 GB/T 294-1994 滚动轴承 三点和四点接触球轴承 外形尺寸
Rolling bearings--Three point and four point contact ball bearings--Boundary dimensions
74 GB/T 296-1994 滚动轴承 双列角接触球轴承 外形尺寸
Rolling bearings--Double row angular contact ball bearings--Boundary dimensions
75 GB/T 297-1994 滚动轴承 圆锥滚子轴承 外形尺寸
Rolling bearings--Tapered roller bearings--Boundary dimensions
76 GB/T 299-1995 滚动轴承 双列圆锥滚子轴承 外形尺寸
Rolling bearings--Metric double row tapered roller bearings--Boundary dimensions
77 GB/T 300-1995 滚动轴承 四列圆锥滚子轴承外形尺寸
Rolling bearings--Four row tapered roller bearings--Boundary dimensions
78 GB/T 301-1995 滚动轴承 推力球轴承 外形尺寸
Rolling bearings--Thrust ball bearings--Boundary dimensions
79 GB/T 304.1-1988 关节轴承 分类
Spherical plain bearings Classification
80 GB/T 304.2-1988 关节轴承 代号方法
Spherical plain bearings Identification code
81 GB/T 304.3-1990 关节轴承 配合
Spherical plain bearings-Fits
82 GB/T 304.9-1981 向心关节轴承 技术条件
Spherical plain radial bearings, joint type--Technical requirements
83 GB/T 304.10-1989 关节轴承公差
Spherical plain bearings-Tolerances
84 GB/T 307.1-1994 滚动轴承 向心轴承 公差
Rolling bearings--Radial bearings--Tolerances
85 GB/T 307.2-1995 滚动轴承 测量和检验的原则及方法
Rolling bearings--Measuring and gauging principles and methods
86 GB/T 307.3-1996 滚动轴承 通用技术规则
Rolling bearings--General technical regulations
87 GB/T 307.4-1994 滚动轴承 推力球轴承 公差
Rolling bearings--Thrust ball bearings--Tolerances
88 GB/T 308-1989 滚动轴承 钢球
Rolling bearings-Steel balls
89 GB/T 309-1984 滚动轴承 滚针
Rolling bearings--Needle rollers
90 GB/T 794-1993 加强半圆头方颈螺栓
Strengthened cap head square neck bolts
91 GB/T 798-1988 活节螺栓
Eye bolts
92 GB/T 799-1988 地脚螺栓
Eyelet bolts
93 GB/T 800-1988 沉头双榫螺栓
Flat countersunk double nib bolts
94 GB/T 802-1988 组合式盖形螺母
Acorn nuts
95 GB/T 804-1988 球面六角螺母
Hexagon nuts with raised face
96 GB/T 805-1988 扣紧螺母
Tight nuts
97 GB/T 806-1988 滚花高螺母
Knurled nut with collar
98 GB/T 807-1988 滚花薄螺母
Knurled nuts
99 GB/T 808-1988 小六角特扁细牙螺母
Small hexagon thin nuts-Fine pitch thread
100 GB/T 809-1988 嵌装圆螺母
Insert round nuts
101 GB/T 810-1988 小圆螺母
Small round nuts
102 GB/T 812-1988 圆螺母
Round nuts
103 GB/T 815-1988 端面带孔圆螺母
Round nuts with drilled holes in one face
104 GB/T 816-1988 侧面带孔圆螺母
Round nuts with set pin holes in side
105 GB/T 817-1988 带槽圆螺母
Slotted round nuts
106 GB/T 818-1985 十字槽盘头螺钉
Cross recessed pan head screws
107 GB/T 819-1985 十字槽沉头螺钉
Cross recessed countersunk head screws
108 GB/T 820-1985 十字槽半沉头螺钉
Cross recessed raised countersunk head screws
109 GB/T 821-1988 方头倒角端紧定螺钉
Square set screws with chamfered end
110 GB/T 822-1988 十字槽圆柱头螺钉
Cross recessed cheese head serews
111 GB/T 823-1988 十字槽小盘头螺钉
Cross recessed small pan head screws
112 GB/T 824-1976 圆柱头内花键螺钉
Screws,fluted socket head
113 GB/T 825-1988 吊环螺钉
Eyebolts
114 GB/T 827-1986 标牌铆钉
Rivets for name plate
115 GB/T 828-1988 开槽盘头定位螺钉
Slotted pan head set setscrews with dog point
116 GB/T 829-1988 开槽圆柱端定位螺钉
Slotted setscrews with dog point
117 GB/T 830-1988 开槽圆柱头轴位螺钉
Slotted cheese head screws with shoulder
118 GB/T 831-1988 开槽无头轴位螺钉
Slotted shoulder screws
119 GB/T 832-1988 开槽带孔球面圆柱头螺钉
Slotted capstan screws
120 GB/T 833-1988 开槽大圆柱头螺钉
121 GB/T 834-1988 滚花高头螺钉
Knurled thumb screws
122 GB/T 835-1988 滚花平头螺钉
Knurled screws
123 GB/T 836-1988 滚花小头螺钉
Knurled screws with small head
124 GB/T 837-1988 开槽盘头不脱出螺钉
Slotted pan head screws with waisted shank
125 GB/T 838-1988 六角头不脱出螺钉
Hexagon screws with waisted shank
126 GB/T 839-1988 滚花头不脱出螺钉
Knurled thumb screws with waisted shank
127 GB/T 840-1988 塑料滚花头螺钉
Plastic diamond knurlhead screws
128 GB/T 845-1985 十字槽盘头自攻螺钉
Cross recessed pan head tapping screws
129 GB/T 846-1985 十字槽沉头自攻螺钉
Cross recessed countersunk head tapping screws
130 GB/T 847-1985 十字槽半沉头自攻螺钉
Cross recessed raised countersunk head tapping screws
131 GB/T 848-1985 小垫圈--A级
Plain washers--Small series--Product grade A
132 GB/T 849-1988 球面垫圈
Weshers with ball face
133 GB/T 850-1988 锥面垫圈
Washers with cone face
134 GB/T 851-1988 开口垫圈
Washers with split
135 GB/T 852-1988 工字钢用方斜垫圈
Square taper washers for I section
136 GB/T 853-1988 槽钢用方斜垫圈
Square taper washers for slot section
137 GB/T 854-1988 单耳止动垫圈
Tab washers with long tab
138 GB/T 855-1988 双耳止动垫圈
Tab washers with long tab and wing
139 GB/T 856-1988 外舌止动垫圈
External tab washers
140 GB/T 858-1988 圆螺母用止动垫圈
Tab washers for round nut
141 GB/T 859-1987 轻型弹簧垫圈
Single coil spring lock washers,Light type
142 GB/T 860-1987 鞍形弹性垫圈
Curved spring washers
143 GB/T 861.1-1987 内齿锁紧垫圈
Lock washers internal teeth
144 GB/T 861.2-1987 内锯齿锁紧垫圈
Serrated lock washers internal teeth
145 GB/T 862.1-1987 外齿锁紧垫圈
Lock washers external teeth
146 GB/T 862.2-1987 外锯齿锁紧垫圈
Serrated lock washers external teeth
147 GB/T 863.1-1986 半圆头铆钉 (粗制)
Round head rivets--Black
148 GB/T 863.2-1986 小半圆头铆钉 (粗制)
Round head rivets with small head--Black
149 GB/T 864-1986 平锥头铆钉 (粗制)
Cone head rivets--Black
150 GB/T 865-1986 沉头铆钉 (粗制)
Countersunk head rivets-Black
151 GB/T 866-1986 半沉头铆钉 (粗制)
Oval countersunk head rivets--Black
152 GB/T 867-1986 半圆头铆钉
Round head rivets
153 GB/T 868-1986 平锥头铆钉
Cone head rivets
154 GB/T 869-1986 沉头铆钉
Countersunk head rivets
155 GB/T 870-1986 半沉头铆钉
Oval countersunk head rivets
156 GB/T 871-1986 扁圆头铆钉
Flat round head rivets
157 GB/T 872-1986 扁平头铆钉
Thin head rivets
158 GB/T 873-1986 扁圆头半空心铆钉
Oval head semi-tubular rivets
159 GB/T 874-1986 120°沉头半空心铆钉
120 degree countersunk head semi-tubular rivets
160 GB/T 875-1986 偏平头半空心铆钉
Thin head semi-tubular rivet
161 GB/T 876-1986 空心铆钉
Tubular rivets
162 GB/T 877-1986 开尾圆锥销
Taper pins with split
163 GB/T 878-1986 螺纹圆柱销
Parallel pins with external thread
164 GB/T 879-1986 弹性圆柱销
Spring-type straight pins—Slotted
165 GB/T 880-1986 带孔销
Pins with split pin hole
166 GB/T 881-1986 螺尾锥销
Taper pins with external thread
167 GB/T 882-1986 销轴
Clevis pins with head
168 GB/T 883-1986 锥销锁紧挡圈
Lock rings with cone pin
169 GB/T 884-1986 螺钉锁紧挡圈
Lock ring with screw
170 GB/T 885-1986 带锁圈的螺钉锁紧挡圈
Lock rings with screw and circlip
171 GB/T 886-1986 轴肩挡圈
Rings for shoulder
172 GB/T 889-1986 1 型非金属嵌件六角锁紧螺母
Prevailing torque type hexagon nuts (with non-metallic insert),style 1
173 GB/T 891-1986 螺钉紧固轴端挡圈
Lock rings at the end of shaft with screw
174 GB/T 892-1986 螺栓紧固轴端挡圈
Lock rings at the end of shaft with bolt
175 GB/T 893.1-1986 孔用弹性挡圈--A型
Circlips for holes--Type A
176 GB/T 893.2-1986 孔用弹性挡圈--B型
Circlips for hole--Type B
177 GB/T 894.1-1986 轴用弹性挡圈--A型
Circlips for shaft--Type A
178 GB/T 894.2-1986 轴用弹性挡圈--B型
Circlips for shaft--Type B
179 GB/T 895.1-1986 孔用钢丝挡圈
Roundwire snap rings for hole
180 GB/T 895.2-1986 轴用钢丝挡圈
Roundwire snap rings for shaft
181 GB/T 896-1986 开口挡圈
"E" rings
182 GB/T 897-1988 双头螺柱
bm=1d Double end studs--bm=1d
183 GB/T 898-1988 双头螺柱
bm=1.25d Double end studs bm=1.25d
184 GB/T 899-1988 双头螺柱
bm=1.5d Double end studs bm=1.5d
185 GB/T 900-1988 双头螺柱
bm=2d Double end studs bm=2d
186 GB/T 901-1988 等长双头螺柱 B级
Double end studs (clamping type)--Product grade B
187 GB/T 902.1-1989 手工焊用焊接螺柱
Weld studs for manual welding
188 GB/T 902.2-1989 机动弧焊用焊接螺柱
Weld studs for arc welding
189 GB/T 902.3-1989 储能焊用焊接螺柱
Weld studs for capacitor discharge welding
190 GB/T 921-1986 钢丝锁圈
Round wire circlips
191 GB/T 922-1986 木螺钉技术条件
Specifications for wood screws
192 GB/T 923-1988 盖形螺母
Acorn nuts
193 GB/T 925-1988 轻型六角自锁螺母
Self-locking nuts,hexagon light
194 GB/T 927-1988 球面六角自锁螺母
Self-locking nuts,hexagon sphere
195 GB/T 929-1988 单耳托板自锁螺母
Self-locking nuts,singlelug, anchor
196 GB/T 930-1988 双耳托板自锁螺母
Self-locking nuts,twolug, anchor
197 GB/T 931-1988 角形托板自锁螺母
Self-locking nuts,angle, anchor
198 GB/T 932-1988 气密单耳托板自锁螺母
Self-locking nuts,singlelug, anchor, sealing,
199 GB/T 933-1988 气密双耳托板自锁螺母
Self-locking nuts,twolug, anchor, sealing
200 GB/T 937-1988 成组游动托板自锁螺母
Self-locking nuts, anchor, floating,Gang channel
201 GB/T 938-1988 游动自锁螺母
Self-locking nuts, floating
202 GB/T 939-1988 单耳托板自锁螺母保护罩
Boots for self-locking nuts, singlelug, anchor
203 GB/T 940-1988 双耳托板自锁螺母保护罩
Boots for self-locking nuts,twolug, anchor
204 GB/T 941-1988 角形托板自锁螺母保护罩
Boots for self-locking nuts,angle, anchor
205 GB/T 943-1988 自锁螺母技术条件
Procurement specification for self-locking nuts
206 GB/T 945-1976 十字槽球面中柱头螺钉
Screws,cross recessed,thin raised cheese head
207 GB/T 946-1988 开槽球面圆柱头轴位螺钉
Slotted raised cheese head with shoulder
208 GB/T 947-1988 开槽球面大圆柱头螺钉
Slotted large raised cheese head screws
209 GB/T 948-1988 开槽沉头不脱出螺钉
Slotted countersunk head screws with waisted shank
210 GB/T 949-1988 开槽半沉头不脱出螺钉
Slotted raised countersunk head screws with waisted shank
211 GB/T 950-1986 十字槽圆头木螺钉
Cross recessed round head wood screws
212 GB/T 951-1986 十字槽沉头木螺钉
Cross recessed countersunk head wood screws
213 GB/T 952-1986 十字槽半沉头木螺钉
Cross recessed raised countersunk head wood screws
214 GB/T 953-1988 等长双头螺柱 C级
Double end studs (clamping type)--Product grade C
215 GB/T 954-1986 120°沉头铆钉
120°degree countersunk head rivets
216 GB/T 955-1987 波形弹性垫圈
Wave spring washers
217 GB/T 956.1-1987 锥形锁紧垫圈
Countersunk external toothed lock washers
218 GB/T 956.2-1987 锥形锯齿锁紧垫圈
Countersunk serrated external toothed lock washers
219 GB/T 959.1-1986 挡圈技术条件--弹性挡圈
Specifications for ring—Circlips
220 GB/T 959.2-1986 挡圈技术条件--钢丝挡圈
Specifications for ring—Round wire snap rings
221 GB/T 959.3-1986 挡圈技术条件--切制挡圈
Specifications for ring—Cutting rings
222 GB/T 960-1986 夹紧挡圈
Grip rings
223 GB/T 961-1988 单耳托板自锁螺母垫片
Spacers for self-locking nuts,singlelug, anchor
224 GB/T 962-1988 双耳托板自锁螺母垫片
Spacers for self-locking nuts,twolug, anchor
225 GB/T 963-1988 角形托板自锁螺母垫片
Spacers for self-locking nuts,angle, anchor
226 GB/T 973-1976 十字槽扁圆头螺钉
Screws,cross recessed,oval head
227 GB/T 974-1976 十字槽120°半沉头螺钉
Screws,cross recessed,120°raised countersunk head
228 GB/T 975-1986 管状铆钉
Pipe type rivets
229 GB/T 1007-1976 小六角较扁螺母
Small hexagon medium thin nuts
230 GB/T 1009-1978 螺母专用技术条件
Specified specifications for nuts
231 GB/T 1011-1986 大扁圆头铆钉
Truss head rivets
232 GB/T 1012-1986 120°半沉头铆钉
120°degree oval countersunk rivets
233 GB/T 1013-1986 平锥头半空心铆钉
Cone head semi-tubuler rivets
234 GB/T 1014-1986 大扁圆头半空心铆钉
Truss head semi-tubuar rivets
235 GB/T 1015-1986 沉头半空心铆钉
Countersunk head semi-tublar rivets
236 GB/T 1016-1986 无头铆钉
Headless rivets
237 GB/T 1017-1978 铆钉专用技术条件
Specified specifications for rivets
238 GB/T 1021-1976 角形垂直单耳止动垫圈
Lock washers with angular upturn tab perpendicular to the lug
239 GB/T 1022-1976 角形单耳止动垫圈
Lock washers with angular upturn tab in line to the lug
240 GB/T 1023-1976 角形垂直外舌止动垫圈
Lock washers with angular upturn tab perpendicular to the external tab
241 GB/T 1024-1976 角形外舌止动垫圈
Lock washers with angular upturn tab in line to the external tab
242 GB/T 1030-1988 内球面垫圈
Inner sphere washers
243 GB/T 1047-1995 管道元件的公称通径
Nominal size for pipe components
244 GB/T 1048-1990 管道元件公称压力
Nominal pressure for pipe components
245 GB/T 1095-1979 平键 键和键槽的剖面尺寸
Parallel keys--Dimensions of cross sections and keyways
246 GB/T 1096-1979 普通平键 型式尺寸
Plain parallel keys--Types and dimensions
247 GB/T 1097-1979 导向平键 型式尺寸
Feather keys--Types and dimensions
248 GB/T 1098-1979 半圆键 键和键槽的剖面尺寸
Semi-circular (Woodruff) keys--Dimensions of cross sections and keyways
249 GB/T 1099-1979 半圆键 型式尺寸
Woodruff keys--Types and dimensions
250 GB/T 1144-1987 矩形花键尺寸、公差和检验
Straight-sided spline—Dimensions tolerances and verification
251 GB/T 1168-1976 螺柱技术条件
Studs--Technical requirements
252 GB/T 1228-1991 钢结构用高强度大六角头螺栓
High strength bolts with large hexagon head for steel structures
253 GB/T 1229-1991 钢结构用高强度大六角螺母
High strength large hexagon nuts for steel structures
254 GB/T 1230-1991 钢结构用高强度垫圈
High strength plain washers for steel structures
255 GB/T 1231-1991 钢结构用高强度大六角头螺拴、大六角螺母、垫圈技术条件
Specifications of high strength bolts with large hexa-gon head, large hexagon nuts, plain washers for steel structures
256 GB/T 1237-1988 紧固件的标记方法
Designation system for fasteners
257 GB/T 1337-1988 六角自锁螺母
Self-locking nuts,hexagon
258 GB/T 1338-1988 小六角扁自锁螺母
Self-locking nuts,reduced hexagon oblate
259 GB/T 1339-1988 小六角自锁螺母
Self-locking nuts,reduced hexagon
260 GB/T 1340-1988 成组游动托板自锁螺母支架
Supports for self-locking nuts,anchor floating,Gang channel
261 GB/T 1356-1988 淅开线圆柱齿轮 基本齿廓
Basic rack tooth profile of involute cylindrical gears
262 GB/T 1357-1987 渐开线圆柱齿轮模数
Modules of involute cyindrical gears
263 GB/T 1563-1979 楔键 键和键槽的剖面尺寸
Taper keys--Cross section dimensions of keys and keyways
264 GB/T 1564-1979 普通楔键 型式尺寸
Taper keys for general use--Types and dimensions
265 GB/T 1565-1979 钩头楔键 型式尺寸
Gib-head taper keys--Types and dimensions
266 GB/T 1566-1979 薄型平键 键和键槽的剖面尺寸
Thin flat keys--Cross section dimensions and keyways
267 GB/T 1567-1979 薄型平键 型式尺寸
Thin flat keys--Types and dimensions
268 GB/T 1840-1989 圆弧圆柱齿轮模数
Modules of cylindrical gear with circular arc profiles
269 GB/T 1974-1980 切向键及其键槽
Tangential keys and keyways
270 GB/T 2362-1990 小模数渐开线圆柱齿轮基本齿廓
Basic rack tooth profile of fine-pitch involute cylindrical gears
271 GB/T 2363-1990 小模数渐开线圆柱齿轮精度
Accuracy of fine-pitch involute cylindrical gears
272 GB/T 2509-1981 滑动轴承铜合金整体轴套形式、尺寸与公差
Copper alloy integrated shaft sleeves for plain bearings--Types, dimensions and tolerances
273 GB/T 2510-1981 滑动轴承铜合金带挡边整体轴套形式、尺寸与公差
Copper alloy integrated shaft sleeves for plain bearings with gears--Types, dimensions and tolerances
274 GB/T 2511-1981 滑动轴承铜合金整体轴套技术条件
Copper alloy integrated shaft sleeves--Technical requirements
275 GB/T 2555-1981 一般用途管法兰连接尺寸
Pipe flange connectors for ordinary use--Mounting dimensions
276 GB/T 2556-1981 一般用途管法兰密封面形状和尺寸
Pipe flanges for ordinary use--Sealing surfaces--Forms and dimensions
277 GB/T 2672-1986 内六角花形盘头螺钉
Hexagon lobular socket pan head screws
278 GB/T 2673-1986 内六角花形沉头螺钉
Hexagon lobular socket countersunk head screws
279 GB/T 2674-1986 内六角花形半沉头螺钉
Hexagon lobular socket raised countersunk head screws
280 GB/T 2685-1981 滑动轴承 粉末冶金筒形轴承型式、尺寸与公差
Powder metallurgy plain bearing--Cylindrical type--Types, dimensions and tolerances
281 GB/T 2686-1981 滑动轴承 粉末冶金带挡边筒形轴承型式、尺寸与公差
Powder metallurgy plain bearing--Rimed cylindrical type--Types, dimensions and tolerances
282 GB/T 2687-1981 滑动轴承 粉末冶金球形轴承型式、尺寸与公差
Powder metallurgy plain bearing--Spherical type--Types, dimensions and tolerances
283 GB/T 2688-1981 滑动轴承 粉末冶金轴承技术条件
Powder metallurgy plain bearing--Technical requirements
284 GB/T 2821-1992 齿轮几何要素代号
Symbols for gear geometrical data
285 GB/T 2889-1994 滑动轴承 术语
Plain bearings--Terms, definitions and classification
286 GB/T 3098.1-1982 紧固件机械性能 螺栓、螺钉和螺柱
Mechanical properties of fasteners--Bolts, screws and studs
287 GB/T 3098.2-1982 紧固件机械性能 螺母
Mechanical properties of fasteners--Nuts
288 GB/T 3098.3-1982 紧固件机械性能 紧定螺钉
Mechanical properties of fasteners--Set screws
289 GB/T 3098.4-1986 紧固件机械性能--细牙螺母
Mechanical properties of fasteners--Nuts with fine pitch thread
290 GB/T 3098.5-1985 紧固件机械性能 自攻螺钉
Mechanical properties of fasteners--Tapping screws
291 GB/T 3098.6-1986 紧固件机械性能 不锈钢螺栓, 螺钉, 螺柱和螺母
Mechanical properties of fasteners--Stainless steel bolts,screws, studs and nuts
292 GB/T 3098.7-1986 紧固件机械性能 自攻锁紧螺钉 粗牙普通螺纹系列
Mechanical properties of fasteners--Thread forming screws--Metric coarse thread series
293 GB/T 3098.8-1992 紧固件机械性能 耐热用螺纹连接副
Mechanical properties of fasteners--Components for bolted connections made mainly from materials with a high temperature strength
294 GB/T 3098.9-1993 紧固件机械性能有效力矩型钢六角锁紧螺母
Mechanical properties of fasteners--Prevailing torque type steel hexagon nuts
295 GB/T 3098.10 -1993 紧固件机械性能 有色金属制造的螺栓、螺钉、螺柱和螺母 Mechanical properties of fasteners-- Bolts, screws, studs and nuts made of non-ferrous metals
296 GB/T 3098.11-1995 紧固件机械性能自钻自攻螺钉
Mechanical properties of fasteners--Self-drilling tapping screws
297 GB/T 3098.13-1996 紧固件机械性能 螺栓与螺钉的扭矩试验和破坏扭矩公称直径1~10mm
Mechanical properties of fasteners--Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm
298 GB/T 3098.12-1996 紧固件机械性能 螺母锥形保证载荷试验
Mechanical properties of fasteners--Cone proof load test on nuts
299 GB/T 3099-1982 螺栓、螺钉、螺母及附件名词术语
Bolts, screws, nuts and accessories--Terminology and nomenclature
300 GB/T 3103.1-1982 紧固件公差 螺栓、螺钉和螺母
Tolerances for fasteners--Bolts, screws and nuts
301 GB/T 3103.2-1982 紧固件公差 用于精密机械的螺栓、螺钉和螺母
Tolerances for fasteners--Bolts, screws and nuts for fine mechanics
302 GB/T 3103.3-1982 紧固件公差 平垫圈
Tolerances for fasteners--Washers
303 GB/T 3103.4-1992 紧固件公差 耐热用螺纹连接副
Tolerances for fasteners--Components for bolted connections made mainly from materials with a high temperature strength
304 GB/T 3104-1982 紧固件 六角产品的对边宽度
Fasteners--Widths across flats of hexagon products
305 GB/T 3105-1982 螺栓和螺钉的头下圆角半径
Radii under the head of bolts and screws
306 GB/T 3106-1982 螺栓、螺钉和螺柱的公称长度和普通螺栓的螺纹长度
Bolts, screws and studs--Nominal lengths, and thread lengths for general purpose bolts
307 GB/T 3162-1991 滑动轴承薄壁轴瓦尺寸、结构要素与公差
Plain bearings—Thin-walled bearing shells—Dimensions, structure elements and tolerances
308 GB/T 3287-1982 可锻铸铁管路连接件技术条件
Technical requirements of malleable cast iron pipe fittings
309 GB/T 3288-1982 可锻铸铁管路连接件验收规则
Delivery requirements of malleable cast iron pipe fittings
310 GB/T 3289.1-1982 可锻铸铁管路连接件型式尺寸 管件结构尺寸表
Malleable cast iron pipe fittings--Type size--Dimensions list of pipe fittings structure
311 GB/T 3289.2-1982 可锻铸铁管路连接件型式尺寸 弯头 内外丝弯头
Malleable cast iron pipe fittings--Type size--Elbows male and female elbows
312 GB/T 3289.3-1982 可锻铸铁管路连接件型式尺寸 45°弯头 45°内外丝弯头
Malleable cast iron pipe fittings--Type size--Elbows 45°, male and female elbows 45°
313 GB/T 3289.4-1982 可锻铸铁管路连接件型式尺寸 异径弯头
Malleable cast iron pipe fittings--Type size--Reducing elbows
314 GB/T 3289.5-1982 可锻铸铁管路连接件型式尺寸 异径内外丝弯头
Malleable cast iron pipe fittings--Type size--Male and female reducing elbows
315 GB/T 3289.6-1982 可锻铸铁管路连接件型式尺寸 侧孔弯头
Malleable cast iron pipe fittings--Type size--Side outlet elbows
316 GB/T 3289.7 -1982 可锻铸铁管路连接件型式尺寸 月弯 内外丝月弯 外丝月弯 Malleable cast iron pipe fittings-- Type size--Return bends, male and female return bends, thread return bends
317 GB/T 3289.8-1982 可锻铸铁管路连接件型式尺寸 45°月弯45°内外丝月弯45°外丝月弯 Malleable cast iron pipe fittings--Type size--Long sweep bends 45°， male and female long sweep bends 45°,male long sweep bends 45°
318 GB/T 3289.9-1982 可锻铸铁管路连接件型式尺寸 U型弯头
Malleable cast iron pipe fittings--Type size--U-Elbows(return bends)
319 GB/T 3289.10-1982 可锻铸铁管路连接件型式尺寸 三通 内外丝三通
Malleable cast iron pipe fittings--Type size--Tees, male and female tees
320 GB/T 3289.11-1982 可锻铸铁管路连接件型式尺寸 异径内外丝三通
Malleable cast iron pipe fittings--Type size--Male and female reducing tees
321 GB/T 3289.12-1982 可锻铸铁管路连接件型式尺寸 中大异径三通
Malleable cast iron pipe fittings--Type size--Medium-large reducing tees [tees(increasing on the branch)]
322 GB/T 3289.13-1982 可锻铸铁管路连接件型式尺寸 侧大异径三通
Malleable cast iron pipe fittings--Type size--Lateral-large reducing tees
323 GB/T 3289.14-1982 可锻铸铁管路连接件型式尺寸 中小异径三通
Malleable cast iron pipe fittings--Type size--Medium-less reducing tees
324 GB/T 3289.15-1982 可锻铸铁管路连接件型式尺寸 侧小异径三通
Malleable cast iron pipe fittings--Type size--Lateral-less reducing tees
325 GB/T 3289.16-1982 可锻铸铁管路连接件型式尺寸 中小偏心异径三通
Malleable cast iron pipe fittings--Type size--Medium-less eccentric reducing tees
326 GB/T 3289.17-1982 可锻铸铁管路连接件型式尺寸 45°三通 Y型三通
Malleable cast iron pipe fittings--Type size--Tees45°, Y pieces(tees)
327 GB/T 3289.18-1982 可锻铸铁管路连接件型式尺寸 Y型异径三通
Malleable cast iron pipe fittings--Type size--Y Piece reducing(tees)
328 GB/T 3289.19-1982 可锻铸铁管路连接件型式尺寸 侧孔三通
Malleable cast iron pipe fittings--Type size--Side outlet tees
329 GB/T 3289.20-1982 可锻铸铁管路连接件型式尺寸 四通
Malleable cast iron pipe fittings--Type size--Crosses
330 GB/T 3289.21-1982 可锻铸铁管路连接件型式尺寸 异径四通
Malleable cast iron pipe fittings--Type size--Reducing crosses
331 GB/T 3289.22-1982 可锻铸铁管路连接件型式尺寸 外接头 内外丝接头
Malleable cast iron pipe fittings--Type size--Male joints(sockets), male and female joints (sockets)
332 GB/T 3289.23-1982 可锻铸铁管路连接件型式尺寸 无方内接头
Malleable cast iron pipe fittings--Type size--No-square inner joint (nipples)
333 GB/T 3289.24-1982 可锻铸铁管路连接件型式尺寸 异径外接头
Malleable cast iron pipe fittings--Type size--Reducing male joints (sockets)
334 GB/T 3289.25-1982 可锻铸铁管路连接件型式尺寸 偏心异径外接头
Malleable cast iron pipe fittings--Type size--Eccentric reducing male joints (sockets)
335 GB/T 3289.26-1982 可锻铸铁管路连接件型式尺寸 内接头
Malleable cast iron pipe fittings--Type size--Inner joints (nipples hexagon)
336 GB/T 3289.27-1982 可锻铸铁管路连接件型式尺寸 异径内接头
Malleable cast iron pipe fittings--Type size--Reducing inner joints(nipples hexagon)
337 GB/T 3289.28-1982 可锻铸铁管路连接件型式尺寸 内外螺丝
Malleable cast iron pipe fittings--Type size--Male and female screws (bushings)
338 GB/T 3289.29-1982 可锻铸铁管路连接件型式尺寸 通丝外接头
Malleable cast iron pipe fittings--Type size--Through thread male joint (sockets)
339 GB/T 3289.30-1982 可锻铸铁管路连接件型式尺寸 锁紧螺母
Malleable cast iron pipe fittings--Type size--Backnuts
340 GB/T 3289.31-1982 可锻铸铁管路连接件型式尺寸 外方管堵
Malleable cast iron pipe fittings--Type size--Outer-square plugs
341 GB/T 3289.32-1982 可锻铸铁管路连接件型式尺寸 带边外方管堵
Malleable cast iron pipe fittings--Type size--Outer-square beaded plugs
342 GB/T 3289.33-1982 可锻铸铁管路连接件型式尺寸 内方管堵
Malleable cast iron pipe fittings--Type size--Inner-square plugs
343 GB/T 3289.34-1982 可锻铸铁管路连接件型式尺寸 管帽
Malleable cast iron pipe fittings--Type size--Tube caps (caps plugs)
344 GB/T 3289.35 -1982 可锻铸铁管路连接件型式尺寸 活接弯头 内外丝活接弯头 Malleable cast iron pipe fittings-- Type size--Union elbows, male and female union elbows
345 GB/T 3289.36-1982 可锻铸铁管路连接件型式尺寸 活接三通
Malleable cast iron pipe fittings--Type size--Union tees
346 GB/T 3289.37-1982 可锻铸铁管路连接件型式尺寸 平形活接头
Malleable cast iron pipe fittings--Type size--Parallel unions
347 GB/T 3289.38-1982 可锻铸铁管路连接件型式尺寸 锥形活接头
Malleable cast iron pipe fittings--Type size--Taper unions
348 GB/T 3289.39-1982 可锻铸铁管路连接件型式尺寸 平形活接头垫圈
Malleable cast iron pipe fittings--Type size--Parallel union gaskets
349 GB/T 3374-1992 齿轮基本术语
Basic terminology of gears
350 GB/T 3478.1-1995 圆柱直齿渐开线花键模数 基本齿廓 公差
Straight cylindrical involute splines--Modules, basic rack profiles and tolerances
351 GB/T 3478.2-1995 圆柱直齿渐开线花键 30°压力角 尺寸表
Straight cylindrical involute splines--30°pressure angle dimenslons tables
352 GB/T 3478.3-1995 圆柱直齿渐开线花键 37.5°压力角 尺寸表
Straight cylindrical involute splines--37.5°pressure angle dimensions tables
353 GB/T 3478.4-1995 圆柱直齿渐开线花键 45°压力角 尺寸表
Straight cylindrical involute splines--45°pressure angle dimensions tables
354 GB/T 3478.5-1995 圆柱直齿渐开线花键 检验方法
Straight cylindrical involute splines--Inspection methods
355 GB/T 3478.6-1995 圆柱直齿渐开线花键 30°压力角 M值和W值
Straight cylindrical involute splines--30°pressurengle M and W values
356 GB/T 3478.7-1995 圆柱直齿渐开线花键 37.5°压力角 M值和W值
Straight cylindrical involute splines--37.5°pressure angle M and W values
357 GB/T 3478.8-1995 圆柱直齿渐开线花键 45°压力角 M值和W值
Straight cylindrical involute splines--45°pressure angle-M and W values
358 GB/T 3478.9-1995 圆柱直齿渐开线花键 量棒
Straight cylindrical involute splines--Measuring pin
359 GB/T 3507-1983 机械式联轴器公称扭矩系列
Nominal torque series of the mechanical coupling
360 GB/T 3632-1995 钢结构用扭剪型高强度螺栓连接副
Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures
360 GB/T 3632-1995 钢结构用扭剪型高强度螺栓连接副
Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures
361 GB/T 3633-1995 钢结构用扭剪型高强度螺栓连接副 技术条件
Technical requirement for sets of torshear type high strength bolt hexagon nut and plain washer for steel structures
362 GB/T 3733.1-1983 卡套式端直通管接头
Straight thread connector--Assembly
363 GB/T 3733.2-1983 卡套式端直通接头体
Straight thread connector--Body
364 GB/T 3734.1-1983 卡套式锥螺纹直通管接头
Male connector--Assembly
365 GB/T 3734.2-1983 卡套式锥螺纹直通接头体
Male connector--Body
366 GB/T 3735.1-1983 卡套式端直通长管接头
Straight thread long connector--Assembly
367 GB/T 3735.2-1983 卡套式端直通长接头体
Straight thread long connector--Body
368 GB/T 3736.1-1983 卡套式锥螺纹长管接头
Male long connector--Assembly
369 GB/T 3736.2-1983 卡套式锥螺纹长接头体
Male long connector--Body
370 GB/T 3737.1-1983 卡套式直通管接头
Union--Assembly
371 GB/T 3737.2-1983 卡套式直通接头体
Union--Body
372 GB/T 3738.1-1983 卡套式端直角管接头
Straight thread elbow--Assembly
373 GB/T 3738.2-1983 卡套式端直角接头体
Straight thread elbow--Body
374 GB/T 3739.1-1983 卡套式锥螺纹直角管接头
Male elbow--Assembly
375 GB/T 3739.2-1983 卡套式锥螺纹直角接头体
Male elbow--Body
376 GB/T 3740.1-1983 卡套式直角管接头
Union elbow--Assembly
377 GB/T 3740.2-1983 卡套式直角接头体
Union elbow--Body
378 GB/T 3741.1-1983 卡套式端三通管接头
Straight thread branch tee--Assembly
379 GB/T 3741.2-1983 卡套式端三通接头体
Straight thread branch tee--Body
380 GB/T 3742.1-1983 卡套式锥螺纹三通管接头
Male branch tee-Assembly
381 GB/T 3742.2-1983 卡套式锥螺纹三通接头体
Male branch tee--body
382 GB/T 3743.1-1983 卡套式端直角三通管接头
Straight thread run tee--Assembly
383 GB/T 3743.2-1983 卡套式端直角三通接头体
Straight thread run tee--Body
384 GB/T 3744.1-1983 卡套式锥螺纹直角三通管接头
Male run tee--Assembly
385 GB/T 3744.2-1983 卡套式锥螺纹直角三通接头体
Male run tee--Body
386 GB/T 3745.1-1983 卡套式三通管接头
Union tee--Assembly
387 GB/T 3745.2-1983 卡套式三通接头体
Union tee--Body
388 GB/T 3746.1-1983 卡套式四通管接头
Union cross-Assembly
389 GB/T 3746.2-1983 卡套式四通接头体
Union cross--Body
390 GB/T 3747.1-1983 卡套式焊接管接头
Weld male connector-Assembly
391 GB/T 3747.2-1983 卡套式焊接接头体
Weld male connector--Body
392 GB/T 3748.1-1983 卡套式隔壁直通管接头
Bulkhead union--Assmbly
393 GB/T 3748.2-1983 卡套式隔壁直通接头体
Bulkhead union--Body
394 GB/T 3749.1-1983 卡套式隔壁直角管接头
Bulkhead union elbow--Assembly
395 GB/T 3749.2-1983 卡套式隔壁直角接头体
Bulkhead union elbow--Body
396 GB/T 3750.1-1983 卡套式铰接管接头
Angle swivel screw--Assembly
397 GB/T 3750.2-1983 卡套式铰接接头体
Angle swivel screw--Body
398 GB/T 3750.3-1983 卡套式铰接六角螺栓
Hollow screws
399 GB/T 3751.1-1983 卡套式压力表管接头
Connector for pressure gauge--Assembly
400 GB/T 3751.2-1983 卡套式压力表接头体
Connector for pressure gauge-Boby
401 GB/T 3752.1-1983 卡套式组合直角管接头
Adjustable elbow--Assembly
402 GB/T 3752.2-1983 卡套式组合直角接头体
Adjustable elbow--Body
403 GB/T 3753.1-1983 卡套式组合三通管接头
Adjustable T-unions--Assembly
404 GB/T 3753.2-1983 卡套式组合三通接头体
Adjustable T-unions--Body
405 GB/T 3754.1-1983 卡套式端对接直通管接头
Straight thread connector for butt joints--Assembly
406 GB/T 3754.2-1983 卡套式端对接直通接头体
Straight thread connector for butt joints--Body
407 GB/T 3755.1-1983 卡套式锥螺纹对接直通管接头
Male connector for butt joints--Assembly
408 GB/T 3755.2-1983 卡套式锥螺纹对接直通接头体
Male connector for butt joints--Body
409 GB/T 3756.1-1983 卡套式对接直通管接头
Union for butt joints--Assembly
410 GB/T 3756.2-1983 卡套式对接直通接头体
Union for butt joints--Body
411 GB/T 3757.1-1983 卡套式端对接直角管接头
Straight thread elbow for butt joints--Assembly
412 GB/T 3757.2-1983 卡套式端对接直角接头体
Straight thread elbow for butt joints--Body
413 GB/T 3758.1-1983 卡套式锥螺纹对接直角管接头
Male elbow for butt joints--Assembly
414 GB/T 3758.2-1983 卡套式锥螺纹对接直角接头体
Male elbow for butt joints--Body
415 GB/T 3759-1983 卡套式管接头用螺母
Bite type tube fittings--Nuts
416 GB/T 3760-1983 卡套式管接头用对接螺母
Bite type tube fittings--Nuts for butt joints
417 GB/T 3761-1983 卡套式管接头用锥体环
Bite type tube fittings--Pressure bush for butt joints
418 GB/T 3762-1983 卡套式管接头用尖角密封垫圈
Bite type tube fittings--Tipping washer
419 GB/T 3763-1983 卡套式管接头用六角薄螺母
Bite type tube fittings--Hexagon thin nuts
420 GB/T 3764-1983 卡套
Ferrule
421 GB/T 3765-1983 卡套式管接头技术条件
Specification for bite type tube fittings
422 GB/T 3832.1-1983 拉刀矩形柄 型式和基本尺寸
Rectangular shanks for broaches--Types and main dimensions
423 GB/T 3832.2-1983 拉刀圆柱形前柄型式和基本尺寸
Round shanks for broaches--Types and main dimensions
424 GB/T 3832.3-1983 拉刀圆柱形后柄型式和基本尺寸
Round follower end for broaches--Types and main dimensions
425 GB/T 3858-1993 液力传动术语
Hydrodynamic drive terminology
426 GB/T 3882-1995 滚动轴承 外球面球轴承和偏心套外形尺寸
Rolling bearings--Insert bearings and eccentric looking collars --Boundary dimensions
427 GB/T 3944-1983 关节轴承 词汇
Spherical plain bearing,joint type--Vocabulary
428 GB/T 4140-1993 输送用平顶链和链轮
Flat-top chains and associated chainwheels for conveyors
429 GB/T 4199-1984 滚动轴承公差定义
Rolling bearings--Tolerances-definitions
430 GB/T 4222-1991 杆端关节轴承 外形尺寸和公差
Spherical plain bearing rod ends—Boundary dimensions and tolerances
431 GB/T 4323-1984 弹性套柱销联轴器
Pin coupling with elastic sleeve
432 GB/T 4603-1984 滚针轴承 重系列 尺寸和公差
Needle roller bearings--Heavy series--Dimensions and tolerances
433 GB/T 4604-1993 滚动轴承 径向游隙
Rolling bearings--Radial internal clearance
434 GB/T 4646-1991 GEC...FSA 型自润滑向心关节轴承外形尺寸
GEC...FSA type maintenance-free spherical plain radia lbearings, joint type—Boundary dimensions
435 GB/T 4648-1996 滚动轴承 圆锥滚子轴承 凸缘外圈 外形尺寸
Rolling bearings--Metric tapered roller bearings--Flanged cups--Boundary dimensions
436 GB/T 4661-1989 滚动轴承 圆柱滚子
Rolling bearings-cylindrical rollers
437 GB/T 4662-1993 滚动轴承 额定静负荷
Rolling bearings--Static load ratings
438 GB/T 4663-1994 滚动轴承 推力圆柱滚子轴承 外形尺寸
Rolling bearings--Cylindrical thrust roller bearings--Boundary dimensions
439 GB/T 4982-1985 夹紧型真空快卸法兰
Vacuum technology clamped type quick release flange
440 GB/T 5014-1985 弹性柱销联轴器
Elastic pin coupling
441 GB/T 5015-1985 弹性柱销齿式联轴器
Gear coupling with elastic pin
442 GB/T 5267-1985 螺纹紧固件电镀层
Electroplated coatings on threaded fasteners
443 GB/T 5269-1985 传动及输送用双节距精密滚子链和链轮
Double pitch precision roller chains and chain wheels for transmission and conveyors
444 GB/T 5272-1985 梅花形弹性联轴器
Coupling with elastic spider
445 GB/T 5276-1985 紧固件 螺栓、螺钉、螺柱及螺母尺寸代号和标注 Fasteners--Bolts,screws,studs and nuts--Symbols and designations of dimensions
446 GB/T 5277-1985 紧固件 螺栓和螺钉通孔
Fasteners--Clearance holes for bolts and screws
447 GB/T 5278-1985 紧固件 开口销孔和金属丝孔
Fasteners--Split pin holes and wireholes
448 GB/T 5279-1985 沉头螺钉 头部形状和测量
Countersunk head screws--Head configuration and gauging
449 GB/T 5280-1985 自攻螺钉用螺纹
Tapping screws thread
450 GB/T 5281-1985 内六角圆柱头轴肩螺钉
Hexagon socket head shoulder screws
451 GB/T 5282-1985 开槽盘头自攻螺钉
Slotted pan head tapping screws
452 GB/T 5283-1985 开槽沉头自攻螺钉
Slotted countersunk head tapping screws
453 GB/T 5284-1985 开槽半沉头自攻螺钉
Slotted raised countersunk head tapping screws
454 GB/T 5285-1985 六角头自攻螺钉
Hexagon head tapping screws
455 GB/T 5286-1985 螺栓、螺钉和螺母用平垫圈 总方案
Plain washers for bolts,screws and nuts--General plan
456 GB/T 5287-1985 特大垫圈 C级
Plain washers--Extra large series--Product grade C
457 GB/T 5625.1-1985 扩口式端直通管接头
Flared type tube fittings--Straight thread connector--Assembly
458 GB/T 5625.2-1985 扩口式端直通管接头体
Flared type tube fittings--Straight thread connector--Body
459 GB/T 5626.1-1985 扩口式锥螺纹直通管接头
Flared type tube fittings--Male connector--Assembly
460 GB/T 5626.2-1985 扩口式锥螺纹直通管接头体
Flared type tube fittings--Male connector-Body
461 GB/T 5627.1-1985 扩口式锥螺纹长管接头
Flared typed tube fittings--Straight taread long connector--Assembly
462 GB/T 5627.2-1985 扩口式锥螺纹长管接头体
Flared type tube fittings--Straight thread long connector--Body
463 GB/T 5628.1-1985 扩口式直通管接头
Flared type tube fittings--Union--Assembly
464 GB/T 5628.2-1985 扩口式直通管接头体
Flared type tube fittings--Union--Body
465 GB/T 5629.1-1985 扩口式锥螺纹直角管接头
Flared type tube fittings--Male elbow--Assembly
466 GB/T 5629.2-1985 扩口式锥螺纹直角管接头体
Flared type tube fittings--Male elbow--Body
467 GB/T 5630.1-1985 扩口式直角管接头
Flared type tube fittings--Union elbow--Assembly
468 GB/T 5630.2-1985 扩口式直角管接头体
Flared type tube fittings--Union elbow--Body
469 GB/T 5631.1-1985 扩口式可调向端直角管接头
Flared type tube fittings--Straight thread elbow-- Assembly
470 GB/T 5631.2-1985 扩口式可调向端直角管接头体
Flared type tube fittings--Straight thread elbow--Body
471 GB/T 5632.1-1985 扩口式组合直角管接头
Flared type tube fittings--Swivel elbow--Assembly
472 GB/T 5632.2-1985 扩口式组合直角管接头体
Flared type tube fittings--Swivel elbow--Body
473 GB/T 5633.1-1985 扩口式可调向端三通管接头
Flared type tube fittings--Straight thread branch tee--Assembly
474 GB/T 5633.2-1985 扩口式可调向端三通管接头体
Flared type tube fittings--Straight thread branch tee --Body
475 GB/T 5634.1-1985 扩口式组合直角三通管接头
Flared type tube fittings--Swivel run tee--Assembly
476 GB/T 5634.2-1985 扩口式组合直角三通管接头体
Flared type tube fittings--Swivel run tee--Body
477 GB/T 5635.1-1985 扩口式锥螺纹三通管接头
Flared type tube fittings--Male branch tee--Assembly
478 GB/T 5635.2-1985 扩口式锥螺纹三通管接头体
Flared type tube fittings--Male branch tee--Body
479 GB/T 5636.1-1985 扩口式变径锥螺纹三通管接头
Flared type tube fittings--Male branch tee reducer-- Assembly
480 GB/T 5636.2-1985 扩口式变径锥螺纹三通管接头体
Flared type tube fittings--Male branch tee reducer--Body
481 GB/T 5637.1-1985 扩口式可调向端直角三通管接头总成
Flared type tube fittings--Straight thread run tee-- Assembly
482 GB/T 5637.2-1985 扩口式可调向端直角三通管接头体
Flared type tube fittings--Straight thread run tee-- Body
483 GB/T 5638.1-1985 扩口式组合三通管接头
Flared type tube fittings--Swivel branch tee--Assembly
484 GB/T 5638.2-1985 扩口式组合三通管接头体
Flared typed tube fittings--Swivel branch tee--Body
485 GB/T 5639.1-1985 扩口式三通管接头
Flared type tube fittings--Union tee--Assembly
486 GB/T 5639.2-1985 扩口式三通管接头体
Flared type tube fittings--Union tee--Boby
487 GB/T 5640.1-1985 扩口式三通变径管接头
Flared type tube fittings--Union tee reducer--Assembly
488 GB/T 5640.2-1985 扩口式三通变径管接头体
Flared type tube fittings--Union tee reducer--Body
489 GB/T 5641.1-1985 扩口式四通管接头
Flared type tube fittings--Union cross--Assembly
490 GB/T 5641.2-1985 扩口式四通管接头体
Flared type tube fittings--Union cross--Body
491 GB/T 5642.1-1985 扩口式焊接管接头
Flared type tube fittings--Weld male connector--Assembly
492 GB/T 5642.2-1985 扩口式焊接管接头体
Flared type tube fittings--Weld male connector--Body
493 GB/T 5643.1-1985 扩口式隔壁直通管接头
Flared type tube fittings--Bulkhead union--Assembly
494 GB/T 5643.2-1985 扩口式隔壁直通管接头体
Flared type tube fittings--Bulkhead union--Body
495 GB/T 5644.1-1985 扩口式隔壁直角管接头
Flared type tube fittings--Bulkhead union elbow--Assembly
496 GB/T 5644.2-1985 扩口式隔壁直角管接头体
Flared type tube fittings--Bulkhead union elbow--Body
497 GB/T 5645.1-1985 扩口式压力表管接头
Flared type tube fittings--Connector for pressure gauge--Assembly
498 GB/T 5645.2-1985 扩口式压力表管接头体
Flared type tube fittings--Connector for pressure gauge--Body
499 GB/T 5646-1985 扩口式管接头管套
Flared type tube fittings--Sleeve
500 GB/T 5647-1985 扩口式 A 型管接头螺母
Flared type tube fittings--Style A nut
501 GB/T 5648-1985 扩口式 B 型管接头螺母
Flared type tube fittings--Style B nut
502 GB/T 5649-1985 扩口式管接头锁紧螺母
Flared type tube fittings--Locknut
503 GB/T 5650-1985 扩口式管接头空心螺栓
Flared type tube fittings--Inverted flare bolts
504 GB/T 5651-1985 扩口式管接头密合垫
Flared type tube fittings--Seat insert
505 GB/T 5652-1985 扩口式管接头锁紧螺母垫圈
Flared type tube fittings--Back-up washer
506 GB/T 5653-1985 扩口式管接头技术条件
Specification for flared type tube fittings
507 GB/T 5779.1-1986 紧固件表面缺陷--螺栓、螺钉和螺柱--一般要求
Surface discontinuities of fasteners on bolts, screws and studs for general requirements
508 GB/T 5779.2-1986 紧固件表面缺陷--螺母--一般要求
Surface discontinuities of fasteners on nuts for general requirements
509 GB/T 5779.3-1986 紧固件表面缺陷--螺栓、螺钉和螺柱--特殊要求
Surface discontinuities of fasteners on bolts screws and studs—Specialrequirements
510 GB/T 5780-1986 六角头螺栓--C级
Hexagon head bolts—Product grade C
511 GB/T 5781-1986 六角头螺栓--全螺纹--C级
Hexagon head bolts—Full thread—Product grade C
512 GB/T 5782-1986 六角头螺栓--A和B级
Hexagon head bolts—Product grades A and B
513 GB/T 5783-1986 六角头螺栓--全螺纹 A和B级
Hexagon head bolts—Full thread—Product grades A and B
514 GB/T 5784-1986 六角头螺栓--细杆 B级
Hexagon head bolts—Reduced shank—Product grade B
515 GB/T 5785-1986 六角头螺栓--细牙--A和B级
Hexagon head bolts—Fine pitch thread—Product grades A and B
516 GB/T 5786-1986 六角头螺栓--细牙--全螺纹--A和B级
Hexagon head bolts—Fine pitch thread—Full thread—Product grades A and B
517 GB/T 5787-1986 六角法兰螺栓--B级
Hexagon flange bolts—Product grade B
518 GB/T 5788-1986 六角法兰螺栓--细杆--B级
Hexagon flange bolts--Reduced shank--Product grade B
519 GB/T 5789-1986 六角法兰螺栓--加大系列--B级
Hexagon flange bolts—Heavy series—Product grade B
520 GB/T 5790-1986 六角法兰螺栓--加大系列--细杆--B级
Hexagon flange bolts—Heavg eries--Product grade B
521 GB/T 5800-1986 滚动轴承 仪器精密轴承
Rolling bearings--Instrument precision bearings
522 GB/T 5801-1994 滚动轴承 轻中系列滚针轴承 外形尺寸和公差
Rolling bearings--Light and medium series needle roller bearings--Boundary dimensions and tolerances
523 GB/T 5837-1993 液力偶合器 型式和基本参数
Fluid coupling--Types and basic specifications
524 GB/T 5843-1986 凸缘联轴器
Flanged coupling
525 GB/T 5844-1986 轮胎式联轴器
Coupling with rubber tyre element
526 GB/T 5859-1994 滚动轴承 推力调心滚子轴承 外形尺寸
Rolling bearings--Self-aligning thrust roller bearings--Boundary dimensions
527 GB/T 5868-1986 滚动轴承安装尺寸
Dimensions for mounting rolling bearings
528 GB/T 6069-1985 滚子链联轴器
Roller chain coupling
529 GB/T 6073-1985 LT 型高弹性摩擦离合器
Type LT highly elastic frictionclutch
530 GB/T 6074-1995 板式链、端接头及槽轮
Leaf chains, clevises and sheaves
531 GB/T 6076-1985 传动用短节距精密套筒链
Short pitch transmission precision bush chains
532 GB/T 6170-1986 1型六角螺母 A和B级
Hexagon nuts, style 1--Product grades A and B
533 GB/T 6171-1986 1型六角螺母 细牙 A和B级
Hexagon nuts, style 1--Fine pitch thread--Product gra des A and B
534 GB/T 6172-1986 六角薄螺母 A和B级 倒角
Hexagon thin nuts--Product grades A and B--Chamfered
535 GB/T 6173-1986 六角薄螺母 细牙 A和B级
Hexagon thin nuts--Fine pitch thread--Product grades A and B
536 GB/T 6174-1986 六角薄螺母 B级 无倒角
Hexagon thin nuts--Product grade B--Unchamfered
537 GB/T 6175-1986 2型六角螺母 A和B级
Hexagon nuts, style 2--Product grades A and B
538 GB/T 6176-1986 2型六角螺母 细牙 A和B级
Hexagon nuts, style 2--Fine pitch thread--Product grades A and B
539 GB/T 6177-1986 六角法兰面螺母 A级 Hexagon nuts with flange--Product grade A
540 GB/T 6178-1986 1型六角开槽螺母 A和B级
Hexagon slotted and castle nuts, style 1--Product grades A and B
541 GB/T 6179-1986 1型六角开槽螺母 C级
Hexagon slotted nuts, style 1--Product grade C
542 GB/T 6180-1986 2型六角开槽螺母 A和B级
Hexagon slotted and castle nuts,style 2--Product grades A and B
543 GB/T 6181-1986 六角开槽薄螺母 A和B级
Hexagon thin slotted nuts--Product grades A and B
544 GB/T 6182-1986 2型非金属嵌件六角锁紧螺母
Prevailing torque type hexagon nuts (with non-metallic insert), style 2
545 GB/T 6183-1986 非金属嵌件六角法兰面锁紧螺母
Prevailing torque type hexagon nuts with flange (with non-metallic insert)
546 GB/T 6184-1986 1型全金属六角锁紧螺母
Prevailing torque type all-metal hexagon nuts, style 1
547 GB/T 6185-1986 2型全金属六角锁紧螺母 5,8,10和12级
Prevailing torque type all-metal hexagon nuts, style 2--Property classes 5,8, 10 and 12
548 GB/T 6186-1986 2型全金属六角锁紧螺母 9级
Prevailing torque type all-metal hexagon nuts, style 2--Property class 9
549 GB/T 6187-1986 全金属六角法兰面锁紧螺母
Prevailing torque type all-metal hexagon nuts with flange
550 GB/T 6188-1986 紧固件用六角花形 T型
Hexagon lobular for fasteners--Type T
551 GB/T 6189-1986 紧固件用六角花形 E型
Hexagon lobular for fasteners--Type E
552 GB/T 6190-1986 内六角花形圆柱头螺钉 4.8级
Hexagon lobular socket head cap screws--Property class 4.8
553 GB/T 6191-1986 内六角花形圆柱头螺钉 8.8级
Hexagon lobular socket head cap screws--Property class 8.8
554 GB/T 6333-1986 电力液压块式制动器
The electro-hydraulic double-shoe brakes
555 GB/T 6334-1986 直流电磁铁块式制动器
DC-electromagnet double-shoe brakes
556 GB/T 6391-1995 滚动轴承 额定动载荷和额定寿命
Rolling bearings--Dynamic load ratings and rating life
557 GB/T 6413-1986 渐开线圆柱齿轮胶合承载能力计算方法
Calculation of scuffing load capacity for involute cylindrical gears
558 GB/T 6443-1986 渐开线圆柱齿轮图样上应注明的尺寸数据
Involute cylindrical gears--Information of the dimensional data to be given on the drawing
559 GB/T 6445.1-1996 滚动轴承 滚轮滚针轴承 外形尺寸
Rolling bearings Needle roller bearings--Track rollers--Boundary dimensions
560 GB/T 6445.2-1996 滚动轴承 滚轮滚针轴承 公差
Rolling bearings--Needle roller bearings-Track rollers--Tolerances
561 GB/T 6559-1986 自攻锁紧螺钉的螺杆 粗牙普通螺纹系列
Screw thread shanks for thread forming screw--Metric coarse thread series
562 GB/T 6560-1986 十字槽盘头自攻锁紧螺钉
Cross recessed pan head thread forming screws
563 GB/T 6561-1986 十字槽沉头自攻锁紧螺钉
Cross recessed countersunk head thread forming screws
564 GB/T 6562-1986 十字槽半沉头自攻锁紧螺钉
Cross recessed raised countersunk head thread forming screws
565 GB/T 6563-1986 六角头自攻锁紧螺钉
Hexagon head thread forming screws
566 GB/T 6564-1986 内六角花形圆柱头自攻锁紧螺钉
Hexagon lobular socket thread forming screws
567 GB/T 6930-1986 滚动轴承词汇
Rolling bearings--Vocabulary
568 GB/T 6931.1-1986 带传动基本术语
Drives using belt--Basic terminology
569 GB/T 6931.2-1986 V 带传动术语
Drives using V-belts and grooved pulleys--Terminology
570 GB/T 6931.3-1986 同步带传动术语
Synchronous belt drives--Terminology
571 GB/T 7217-1987 凸缘外圈向心球轴承 凸缘尺寸
Radial ball bearings with flanged outer ring--Flange dimensions
572 GB/T 7218-1995 滚动轴承 凸缘外圈微型向心球轴承外形尺寸
Rolling bearings--Miniature radial ball bearings with flanged outer ring Boundary dimensions
573 GB/T 7244-1987 重型弹簧垫圈
Single coil spring lock washers, Heavy type
574 GB/T 7245-1987 鞍形弹簧垫圈
Curved single coil spring lock washers
575 GB/T 7246-1987 波形弹簧垫圈
Wave single coil spring lock washers
576 GB/T 7308-1987 滑动轴承薄壁翻边轴瓦尺寸、公差及检验方法
Plain bearings--Thin-walled flanged half bearings--Dimensions, tolerances and methods of checking
577 GB/T 7549-1987 球笼式同步万向联轴器型式、基本参数和主要尺寸
Synchronizing universal coupling with ball and sacket--Type, foundational parameters and main dimensions
578 GB/T 7550-1987 球笼式同步万向联轴器试验方法
Synchroizing universal coupling with ball and sacket
579 GB/T 7559-1987 纤维增强塑料层板螺栓连接挤压强度试验方法
FRP Laminates-test method for bearing strength by bolted joints
580 GB/T 7809-1995 滚动轴承 外球面球轴承座外形尺寸
Roliing bearings--Housings for insert bearing boundary dimensions
581 GB/T 7810-1995 滚动轴承 带座外球面球轴承外形尺寸
Rolling bearings--Insert bearing units boundary dimensions
582 GB/T 7811-1987 滚动轴承参数符号
Rolling bearings--Symbols for quantities
583 GB/T 7948-1987 塑料轴承极限PV试验方法
Test method for PV limit of plastics bearings
584 GB/T 8259-1987 卡箍式柔性管接头技术条件
Specification for flexible coupling of housing
585 GB/T 8260-1987 卡箍式柔性环型管接头
Flexible coupling of housing for pipe end with rib ring
586 GB/T 8261-1987 卡箍式柔性肩型管接头
Flexible coupling of housing for pipe end with shoulder
587 GB/T 8262-1987 圆头椭圆颈螺栓
Bolts,round head with oval neck
588 GB/T 8350-1987 输送链、附件和链轮
Conveyor chains, attachments and chain wheels
589 GB/T 8542-1987 透平齿轮传动装置技术条件
Spcification for turbine gearings
590 GB/T 8597-1988 滚动轴承包装
Rolling bearings-packaging and packing
591 GB/T 9065.1-1988 液压软管接头 连接尺寸 扩口式
Hydraulic fluid power--Hose connector--Connecting dimension (Part Ⅰ--Flare type)
592 GB/T 9065.2-1988 液压软管接头 连接尺寸 卡套式
Hydraulic fluid power--Hose connector--Connecting dimension (Part Ⅱ--Insert type)
593 GB/T 9065.3-1988 液压软管接头 连接尺寸 焊接式或快换式
Hydraulic fluid power--Hose connector--Connecting dimension (Part Ⅲ--Welding or quick-action type)
594 GB/T 9074.1-1988 十字槽盘头螺钉和平垫圈组合件
Cross recessed pan head screw and plain washer assemblies
595 GB/T 9074.2-1988 十字槽盘头螺钉和外锯齿锁紧垫圈组合件
Cross recessed pan head screw and serrated lock washer external teeth assemblies
596 GB/T 9074.3-1988 十字槽盘头螺钉和弹簧垫圈组合件
Cross recessed pan head screw and single coil spring lock washer assemblies
597 GB/T 9074.4-1988 十字槽盘头螺钉, 弹簧垫圈和平垫圈组合件
Cross recessed pan head screw,single coil spring lock washer and plain washer assemblies
598 GB/T 9074.5-1988 十字槽小盘头螺钉和平垫圈组合件
Cross recessed small pan head screw and small plain washer assemblies
599 GB/T 9074.6-1988 十字槽小盘头螺钉和大垫圈组合件
Cress recessed small pan head serew and big plain washer assemblies
600 GB/T 9074.7-1988 十字槽小盘头螺钉和弹簧垫圈组合件
Cross recessed small pan head screw and single coil spring lock washer assemblies
